An Easy Instruction for Bathtub Installation
An Easy Instruction for Bathtub Installation
Blog Article
What're your insights and beliefs on How to Install a Bathtub?
Installing a bath tub isn't precisely brain surgery, but it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is readily obtainable, the task can relocate rapidly; if you have to open up a wall to remove the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either case, the job is within a house handyman's skills, although you will require an assistant to move out the old bathtub and also set in the new one. Ensure you have qualified yourself for the task and also fit attempting it. Rather than hiring a contractor to take over a halfway-completed task, it is far better to consider utilizing one prior to you begin. Chances are you might need a professional plumber to make tube links.
This short article will certainly help you set up a brand-new bath tub in your washroom if you have already gotten a new tub as well as do not require to transform the setup of your previous supply of water pipes.
Your devices and material checklist ought to make up the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, activate the taps to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be fairly troublesome because of the limited gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Prior to carrying on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the placing opening in the bath/basin making sure that the washers are in area in between the faucet as well as the sink. Protect the faucet in position with the maker given backnut. As soon as the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former kind needs to be attached to the faucet ends first, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Utilizing the two wood boards under its feet, put the tub in the required setting. The wooden boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The next objective is to make certain that the bathtub is leveled all round. This can be attained by checking the spirit level and readjusting the feet on the bathtub until the level reads degree.
To mount faucets, fit all-time low of the furthest flexible tap connector to the proper supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water system as well as inspect all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the bathtub and additionally examine the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the maker's user's manual. Tiling and sealing around the tub must wait until the tub has been made use of at least when as this will certainly resolve it right into its last setting.
Getting ready for the Installment
First of all, the supporting frame supplied with the bathroom needs to be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is important to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the flexible tap ports to the bottom of the two taps using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its last position.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, causing issues with moisture as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealer can fracture rather early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently readily available on the marketplace. It is recommended to fit the tiles utilizing waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I imagined sharing that piece was a good idea. In case you enjoyed our blog entry if you please make sure you remember to share it. We thank you for reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
We're ready, are you? Report this page